Iron Grey
ToccaCharcoal with faint horizontal banding.
Images are for illustration only and include computer-generated visualisations; stone varies from slab to slab and batch to batch, so approve a physical sample before you order.
Request a quote for this colourWhatsApp – Homeowner (Durban)072 978 0293WhatsApp – Trade & projects069 053 7865Ask about a sample / viewing
| Material | Sintered stone |
|---|---|
| Brand / series | Luxen |
| Finish | Confirm with us |
| Thickness | 12 mm |
| Slab size | 3200 × 1600 mm |
| Suited to | Kitchen worktops, Bathroom vanities, Cladding & walls, Splashbacks |
| Ask us about | Outdoor / braai – confirm for your project, Flooring – confirm for your project |
Missing details need confirmation. Listed specifications are individual values; confirm the required combination and suitability for your project.
Outdoor, cladding and flooring depend on the product, finish, slip resistance and fixing.
Copy a WhatsApp number
About Sintered stone
Mineral surface, pressed and fired; no resin binder.
A dark charcoal ground with faint horizontal banding, like vein-cut stone. The lines are low in contrast, so the surface reads as near-black with a subtle linear grain.
Sintered stone is made from natural minerals, pressed under great pressure and fired at high temperature until the particles fuse. There is no resin binder. Thin slabs need careful fabrication: full support, engineered edges and well-planned mitres.
Strengths
- Hard-wearing. Polished faces can show fine marks more readily than matt; ask for your series’ data sheet.
- Very low absorption on the Dekton and Luxen data sheets; no sealing.
Considerations
- Dekton and Luxen data sheets report thermal-shock resistance. Use trivets all the same.
- Possible for selected products and finishes; ask StoneCo which suit your project.
- Specialist tooling; thin slabs (Dekton 8 and 12 mm, Luxen 12 mm) need full support and engineered edges.
Planning your project
Review confirmed specifications and uses, and what to ask us about.
Layout, joints and supports
Joints, supports, edge build-up and cut-outs depend on the agreed layout. Send a rough sketch. Final drawings, measurements, openings and material approval are needed before cutting.
What affects your quote?
Quantity and layout, selected specification, edges and cut-outs, fabrication, delivery and installation scope all affect the quotation.
What happens after you enquire?
The office reviews your request and confirms specification and scope before quoting. Final measurements, drawings and material approval precede cutting.
Samples and visits
A photograph introduces the look; a sample helps you judge colour and finish in your own light. A sample does not show the complete slab pattern. Contact us to confirm current arrangements before you travel.
Ask about a sample / viewingCurrent technical evidence
The chapter PDF is a catalogue, not a certified datasheet. Request a current technical sheet for your specification.
Questions about Sintered stone
How much does this material vary?
Low to medium; veined designs may repeat across slabs.
How should I judge a sample?
A photograph introduces the look; a sample helps you judge colour and finish in your own light. A sample shows colour, finish and texture, but not the full pattern of a slab. For natural stone, discuss how the selected pieces and their vein direction will be reviewed before fabrication.
How do I care for the surface?
A damp cloth and a mild cleaner are usually enough. No sealing is needed. Avoid abrasive pads and powders on polished faces. On textured Tocca surfaces, a soft brush lifts dirt from the relief. Use trivets and chopping boards, as with any worktop.
Can I use it outdoors?
Possible for selected products and finishes; ask StoneCo which suit your project.
How do I choose an edge?
An edge is the part of a top you touch most. The profile you can have depends on the material, the thickness and how the piece is supported, so choose it with a sample of the edge in hand.
Related colours
Speak to StoneCo
Contact us before travelling to confirm viewing arrangements.
Verulam
MRA Industrial Park, 8 Garland Street
031 837 2847 · Directions
Durban
18 Westmeath Avenue, Bonela
031 837 2848 · Directions
